Why is my Kenmore refrigerator freezer not freezing?
The freezer in a Kenmore freezer may not keep food frozen for numerous reasons such as frozen evaporator coils, leaky refrigerator hoses, a too-crowded freezer, a clogged defrost drain or a malfunctioning or broken thermostat.
How do I reset my Kenmore bottom freezer refrigerator?
Open one refrigerator door and press the “Ultra Ice” and “Home” buttons simultaneously for five seconds to turn off the refrigerator’s controls. Unplug the refrigerator’s power cord from the wall outlet. Reconnect the power cord to the wall outlet. The refrigerator is now reset.
Where is the defrost drain on a Kenmore bottom freezer refrigerator?
A drain hole is located along the bottom of your freezer compartment. The water from the melted ice and frost drains through a short tube and into a pan beneath the refrigerator, where it evaporates.
Why is my freezer frosting up and fridge not working?
Be sure the vents on the back of the freezer compartment aren’t blocked by boxes of ice cream or frozen vegetables—the vents have to be clear for cold air to circulate. Vacuum the coils under or behind the fridge. Plug in the fridge and make sure the fan runs when the compressor is running.
What should a Kenmore freezer be set at?
Ideal Freezer Temperature Kenmore recommends setting your freezer compartment between 0 and 2 Fahrenheit or -16 or -17 Celsius. Food is safely frozen at this temperature, reducing the risk of food thawing out and spoiling. Slightly lower than recommended is better than slightly higher.
How do you test a Kenmore refrigerator?
Enter the diagnostic mode by pressing and holding the Lock button for 3 seconds, then press and hold the Freezer and Refrigerator buttons while pressing the Acela Ice button 5 times. The digital display will show operating time (number of minutes it’s been plugged in).
How do you troubleshoot a Kenmore refrigerator?
If your Kenmore side-by-side doesn’t run, ensure the cord is plugged firmly into the outlet and check your electrical panel. If the breaker has tripped, reset it. If there is power running to the appliance, your refrigerator may be in the defrost cycle and will run when it ends, which typically takes 30 minutes.
How do I run a diagnostic on my Kenmore refrigerator?
How do you force defrost on a Kenmore refrigerator?
Here’s the procedure to use the forced defrost mode:
- Hold the refrigerator door light switch closed.
- Press the Refrigerator Temperature DOWN /- keypad 3 times consecutively.
- Release the refrigerator door light switch.
- The control will display F- d to confirm entry into the Forced Defrost Mode.
Where is the defrost drain on Kenmore Elite?
Locate the drain tube inside your Kenmore refrigerator. This will depend on your specific Kenmore model. Some of the Elite models, for example, have the drain placed beneath the false floor of the unit. In this case you will have to remove the false floor before proceeding.
Why is my fridge cold but freezer warm?
The most common cause for this condition is a problem with the defrost system. If the refrigerator freezer is cold but the refrigerator is warm, the evaporator fan motor might have failed. Every refrigerator has a set of coils called an evaporator.
What are the problems with Kenmore refrigerators?
Some of the more common Kenmore refrigerator issues include temperature control problems, noisy ice makers, or condenser fans that keep running even after the fridge has reached a designated temperature.
Why is my Kenmore refrigerator not cold enough?
If the condenser coils are dirty, they won’t dissipate the heat effectively. As debris builds up on the coils, the refrigerator becomes less efficient, causing the refrigerator to work harder to cool down. If the coils are significantly dirty, the refrigerator will not be able to maintain the proper temperature.
Why is my Kenmore freezer leaking water?
One of the most common causes of a leaking refrigerator freezer is a clogged drain line. When ice or food debris gets stuck down inside this line, it will prevent water from properly traveling through.
What does Kenmore Elite refrigerator error if mean?
Kenmore elite refrigerator error code er if (er 1f) This error occurs when there is no signal from the icing fan motor to the main control board for longer than 114 seconds. If you see the code on the display, please, check the fan in the back of the freezer. The fan’s mission is blowing air toward the ice maker.