Popular lifehacks

What is a SWD connector?

What is a SWD connector?

Serial Wire Debug (SWD) is a 2-pin (SWDIO/SWCLK) electrical alternative JTAG interface that has the same JTAG protocol on top. The Debug Port (DP) and the Access Port (AP), and the physical connection to the debugger is part of the DP.

What is the role of the SWD connector?

The 10-pin, 0.05″ JTAG/SWD connector offers ITM and DWT trace information. In SWD mode, two pins are used for debugging: one bi-directional pin (SWDIO) transfers the information and the second pin (SWDCLK) clocks the data. A third pin (SWO) delivers the trace data at minimum system cost.

What does SWD stand for?


Acronym Definition
SWD Solid Waste Data
SWD Surface Water Detention
SWD Special Weapons Depot
SWD Standing Wave Distribution

How do you use SWD?

In this wiki, you will learn how to use SWD Interface to debug your Arduino boards via the J-Link Debug Programmer….Connect as followed:

  1. SWCLK (Wio Terminal) -> SWCLK (J-Link Debug Programmer Pin 7)
  2. SWDIO (Wio Terminal) -> SWDIO (J-Link Debug Programmer Pin 9)
  3. GND (Wio Terminal) -> GND (J-Link Debug Programmer Pin 4)

How does SWD work?

Short Wave Diathermy (SWD) is a treatment that uses electromagnetic energy to produce deep heating in joints and soft tissues. This form of heat can be applied to deeper structures than other forms of heat treatment.

What is ARM JTAG?

ARM JTAG 20. The ARM JTAG 20 connector is a 20-way 2.54mm pitch connector. It can be used in either standard JTAG (IEEE 1149.1) mode or Serial Wire Debug (SWD) mode.

What is SWD in physiotherapy?

What is tuning in SWD?

The shortwave diathermy unit should be tuned to low power as per patient tolerance, and the meter readings should be properly documented. Heating localization depends on the coupling of radio waves to the patient.

What is a JTAG adapter?

​JTAG is a common hardware interface that provides your computer with a way to communicate directly with the chips on a board. It was originally developed by a consortium, the Joint (European) Test Access Group, in the mid-80s to address the increasing difficulty of testing printed circuit boards (PCBs).

Is JTAG used for programming?

The JTAG interface can not only be used for testing, but also as a JTAG programmer to program devices on your PCBA’s. Flash memories, FPGA’s, CPLD’s, microcontrollers (embedded flash) and serial devices like I2C, SPI and PMBus devices can be programmed via their four port JTAG interface or via surrounding JTAG devices.

How does the SWD interface work with the CPU?

In addition to the debug signals, ARM’s SWD interface also specifies a dedicated pin which allows the target CPU to output specific data like printf output on a dedicates pin via UART or Manchester protocol. This pin is unidirectional, so it is not possible to send data to the target CPU on this pin.

Is the SWD interface the same as the JTAG interface?

SWD, also known as Serial Wire Debug is a 2-pin interface (SWDIO/SWCLK) of which it’s also an alternative JTAG interface that has the same JTAG protocol. SWD uses an ARM CPU standard bi-directional wire protocol, defined in the ARM Debug programmer. Before you start, you will need the following materials:

What kind of wire protocol does SWD use?

SWD uses an Arm standard bi-directional wire protocol, defined in the Arm Debug Interface v5, to pass data to and from the debugger and the target system in a highly efficient and standard way.

Where are the SWD interface pads on a PCBA?

For Wio Terminal, the SWD interface pads are on the bottom of the front side of Wio Terminal (Bare PCBA without casing). There are three jumper wires that need to be led out: Once the jumper wires are soldered on, we can connect them to the J-Link Debug programmer following the SWD Pin Map: