Users' questions

How far apart should vertical studs be?

How far apart should vertical studs be?

When you’re ready to fill in your frame with timber studs and noggings, mark the floor plate at intervals to show where the vertical studs are (they should be 600mm apart).

What is the maximum distance between studs?

Load-Bearing Studs Wall stud spacing is typically 16 inches on center for all load-bearing walls. In some areas and in some situations it’s permissible to use 24-inch spacing for two-by-four stud walls supporting only a roof above, or for two-by-six walls supporting one story and a roof above.

What is the space between studs called?

The cavities between the studs are called bays (or stud bays).

Why are wall studs 16 inches apart?

The first and most obvious reason for 16 inch stud spacing is that this is what most building codes call for in terms of structural integrity. So even if you’re building a wall that was completely non-load bearing, you should still layout your wall studs at 16 inches on center.

How narrow can a stud wall be?

9.5mm and 12.5mm. If using 12.5mm the studs must be placed no further apart than 600mm and if using 9.5mm then 400mm is the maximum (if using plasterboard on a ceiling always use 12.5mm as it will not sag).

Are studs every 12 inches?

When a home is framed, the wall studs are usually spaced 16 or 24 inches apart. If you start in a corner and measure out 16 inches and you don’t find a stud, you should find one at 24 inches. Those are usually mounted on the side of studs, so that’s a good starting point for finding them.

What are common studs?

Common studs are vertical members which transfer loads vertically to bottom plates. They are usually evenly spaced to suit loads, lining and cladding fixing. Spacings are generally 450 or 600 mm, depending on the roof cladding. Common studs should be reinforced at points of concentrated loads.

Should you drill into studs?

Are You Supposed to drill into a Stud? In most situations drilling into the stud is the best option, but if you’re trying to hang a small lightweight picture or decoration it may not be necessary, you maybe be able to get by with just drilling a hole into the drywall and using a drywall anchor.

Can you space studs 24 on Center?

Wood-framed houses have traditionally been built with 2×4 studs spaced 16-inches on-center. Research has shown exterior framed walls can be adequately supported by 2×6 studs spaced 24-inches on-center.

Can studs be 24 apart?

To summarize, studs at 24-inch spacing will save money and resources, and are safe. With 2x6s, it’s a no-brainer for most residential construction—they’re plenty strong in nearly any configuration. With 2×4 studs you can also get by with 24-inch spacing, but walls should be 9 feet tall or less and the loads modest.

What should be the spacing between wall studs?

Proper Wall Stud Spacing. It’s not uncommon in older homes to find interior walls with studs set 24 inches on center, or even 12 inches on center or anywhere in between.

How big should the studs be on a non load bearing wall?

Load-bearing wall studs are usually 16 inches apart, on-center. This predictable spacing lets you easily find studs when trying to hang a picture, install shelves, or put in new kitchen wall cabinets, among other projects. 24 Inches On-Center Non-load-bearing walls can have vertical studs spaced as far apart as 24 inches, on-center.

How is the proper distance between studs measured?

This distance is measured from the center of one stud to the center of the stud next to it. So, what is the proper distance between studs? The studs in most framed homes are positioned between 16 or 24 inches apart.

What’s the difference between exterior and exterior wall studs?

Exterior walls also are usually load-bearing while walls that don’t have walls, posts, or other supports directly above or below them in the structure aren’t likely to be load-bearing. Load-bearing wall studs are usually 16 inches apart, on-center.